Low-E Coated Glass for the Philippines
Solar control for a hot humid climate · Off-line capped at 3,210 × 6,000 mm · Priced against your schedule
We supply Low-E coated glass for Philippine commercial facades, where the coating keeps solar heat out, not warmth in. Off-line coated panels are capped at 3,210 × 6,000 mm by the coating line, so anything larger needs another route. Coating is applied before tempering, and the edge deleted before the unit is sealed. Priced against your glass schedule.
Quote against your drawing within one working day. Send the glass schedule, build-up and destination port.
WhatsApp / phone: +86 138 3303 3053
Email: info@cnglassworks.com
What drives the price of Low-E glass?
Low-E is a coating operation on top of a glass operation, and the coating line's size limit is what usually decides the price rather than the glass itself.
| Cost component | What it covers | What moves it |
|---|---|---|
| Base glass | Clear, low-iron or tinted float | Whether a neutral colour is required, which pushes towards low-iron |
| Coating | Off-line sputtered or on-line pyrolytic | Off-line performs better but is capped at 3,210 × 6,000 mm and needs edge deletion; on-line is durable and can be used monolithic |
| Edge deletion | Removing the coating from the sealing zone | Required for off-line coated glass going into a sealed unit — skipping it causes seal failure |
| Packing and freight | ISPM 15 crates, sea freight | Whether the panel ships monolithic or as a sealed unit |
Send the elevation, the target SHGC and the destination port. Written price within one working day.
Low-E glass price Philippines: Price from USD ___ per sqm FOB Qinzhou. Coating type, light transmission and whether the unit is monolithic or sealed change the number, so we quote per schedule.
What Low-E glass do you supply, and in what sizes?
| Item | Range |
|---|---|
| Coating type | Off-line (sputtered, soft coat) or on-line (pyrolytic, hard coat) |
| Off-line maximum panel | 3,210 × 6,000 mm |
| Thickness | 4, 5, 6, 8, 10, 12 mm |
| Base glass | Clear, low-iron, tinted |
| Performance data | SHGC, U-value, visible light transmission to EN 410 / EN 673 |
| Build-ups | Monolithic (on-line only), or sealed unit with argon |
| Edge | Coating deleted at the sealing zone for off-line coated units |
The 3,210 × 6,000 mm ceiling is the coating line, not the tempering furnace. A 12 m jumbo panel cannot be off-line coated.
Why do Philippine facades want a different Low-E?
A European specification optimises for keeping heat in. In Manila the load is reversed, and copying a European coated product usually produces a facade that is too dark and still too hot.
- SHGC matters more than U-value. Solar heat gain coefficient governs how much radiant heat enters. A low U-value with a high SHGC still produces an overheated room in a tropical facade.
- Too low a VLT makes the building gloomy. Driving SHGC down by darkening the coating pushes visible light transmission below about 30%, and the lighting load then rises. The balance point for most Manila offices sits around SHGC 0.25–0.35 with VLT 40–55%.
- Humidity punishes soft coats at the edge. An off-line coating that is not edge-deleted, or a monolithic soft coat exposed at the edge, degrades from the perimeter inward. That is a specification error, not a product failure.
Off-line or on-line — which Low-E should I choose?
| Property | Off-line (sputtered) | On-line (pyrolytic) |
|---|---|---|
| Performance | Better SHGC and U-value for the same VLT | Moderate, but stable |
| Durability | Soft coat — must be inside a sealed unit, edge deleted | Hard coat — can be monolithic and exposed |
| Maximum panel | 3,210 × 6,000 mm | Larger, limited by the float line |
| Best for | Sealed units in a curtain wall, where performance is the driver | Monolithic retrofit glazing, or where a hard coat is needed |
Questions Philippine buyers ask first
Can Low-E glass be tempered?
Off-line coated glass is coated first, then tempered, and the coating is designed to survive the tempering cycle. On-line coated glass can also be tempered. What cannot happen is coating a panel after tempering — so the order of operations is fixed, and it is why the size limit comes from the coating line.
Why is the maximum Low-E panel only 3,210 × 6,000 mm?
Because the sputtering line is smaller than the tempering furnace. If a project needs a 12 m coated panel, it cannot be made off-line. The alternatives are an on-line hard coat, a tinted body glass, or a split panel with a visible joint.
How long does the coating last?
An off-line soft coat sealed inside a unit lasts the life of the unit, provided the edge is deleted and the seal is intact. An exposed soft coat at an edge or a monolithic installation degrades within a few years in coastal humidity. On-line hard coats are durable enough to be exposed.
Do I need argon with Low-E?
For a U-value target below about 1.8 W/m²K, yes. Low-E alone reduces radiant transfer; argon reduces conductive transfer through the cavity. The two are normally specified together.
Tell us the build-up, the quantity and the destination port. You get a specification review and a written price within one working day — reviewed by an engineer, not a bot.
Other glass we ship to the Philippines
- Tempered glass
- Laminated safety glass
- Insulating glass units
- Jumbo glass to 3,660 × 12,000 mm
- Fire-rated glass
Lead times on this page were verified against factory records in November 2026. Prices are issued only against a drawing or glass schedule, in writing, and are valid for 30 days from issue.