Can tempered glass be cut after tempering?
No. Tempered glass cannot be cut, drilled, notched or edge-polished after tempering — the pane fragments. Tempering locks a stress pattern into the glass, and any cut through that pattern releases it: the sheet breaks into small blunt pieces within a second or two. Sizes, holes and edge profiles have to be fixed before the glass goes into the furnace, which is why we work from approved shop drawings and quote 4–19 mm with 7–15 days for production.
It is not a factory quirk: it is the property that makes tempered glass safe — it breaks into gravel, not shards. Buyers who expect to trim it on site learn the rule after the crate is open.
Why does a cut destroy a tempered pane?
Tempering heats the glass to roughly 620–700 °C, then quenches both faces with air. The skin cools faster than the core, so the surface ends in compression and the core in tension — a balanced pair of forces held inside the sheet. EN 12150-1 and GB 15763.2 require at least 90 MPa of surface compressive stress, which lifts bending strength to four to five times that of annealed glass.
The balance is the whole mechanism. Score a line, drill a hole or grind an edge and you cut through the compressed skin at that point; the tension underneath has nothing holding it back, a crack runs at speed across the pane, and the stored energy dumps into the fracture. EN 12150-1 asks for at least 40 fragments in a 50 × 50 mm square precisely because the break is meant to be total and blunt.
What can and cannot be done to a pane after tempering?
| Operation | Possible after tempering? |
|---|---|
| Cut to a smaller size | No — the pane fragments immediately |
| Drill or enlarge a hole | No — same release, crack starts at the hole |
| Grind or re-polish an edge | No — the edge carries the stress; polishing it removes the temper |
| Notch a corner, cut a cut-out for a hinge | No — every cut-out is made before tempering |
| Sandblast, acid-etch or print a pattern | Yes, within limits — surface treatment only, no cut into the edge |
| Apply safety film, laminate, or fit hardware | Yes, after tempering |
| Waterjet "cutting" a tempered sheet | Technically cuts, but the edge is no longer tempered and no standard accepts it |
So how do you get a tempered panel that actually fits?
You fix the number before the glass is tempered, not after. The sequence we run for Philippine projects:
- Site measure and template. Measure the finished opening, not the old pane. Out-of-square openings are normal in fit-out work; a template transfers that error instead of hiding it.
- Shop drawing approval. Sizes, thickness, hole positions, edge profile and hardware cut-outs on one drawing, approved in writing before cutting. This is where a 5 mm error costs nothing.
- Cut annealed glass to plus or minus 1 mm, with the diagonal of panels over 2 m held to about plus or minus 2 mm.
- Edge work and drilling — flat polish, bevel or round edge, holes drilled with a minimum edge distance of twice the glass thickness.
- Temper, then inspect for bow and roller wave, then pack upright in a crate.
Allow 7–15 days for that cycle at our Qinzhou plant, before sea freight starts.
What thickness range is available, and what must be decided before tempering?
| Thickness | Typical Philippine use | Decide before tempering |
|---|---|---|
| 4–5 mm | Interior partitions, cabinet doors, small fixed lites | Final size; clean or polished edge |
| 6 mm | Shopfronts, office partitions, window replacement | Hole positions for patch fittings |
| 8 mm | Framed shower doors, wardrobe sliding panels | Hinge and handle cut-outs |
| 10 mm | Frameless shower enclosures, glass doors | Hinge holes, handle holes, notch for the floor clamp |
| 12 mm | Frameless doors, glass balustrade infill | Spigot positions, corner radius |
| 15 mm | Structural balustrade, heavy traffic doors | Every fixing point and load calculation |
| 19 mm | Structural fins, table tops, feature floors | Engineering drawing and full hole schedule |
Can a local shop cut it down for me?
No. Reducing a tempered pane back to a cuttable state means annealing it, and annealing means a tempering furnace — a glazing shop does not have one, and a factory will not run a furnace to save one sheet. Waterjet cutting is sometimes offered as a workaround: it will cut the glass, but the cut edge is annealed, the pane no longer meets the standard it was supplied against, and any warranty claim on that panel is gone.
What if the sizes are wrong on site?
Three options, in the order buyers usually take them:
- Remake. 7–15 days production, then 7–12 days sea freight to Manila, 10–15 days to Cebu, 14–20 days to Davao. The pane is paid for twice and the schedule slips a month.
- Adjust the opening. For an error of a few millimetres, packing the frame is cheaper than a new panel — where the frame allows it.
- Split the panel. Two smaller panes and a mullion, sometimes cheaper than one large remake, but it changes the elevation and needs the consultant's approval.
What paperwork does a Manila shipment need?
Correct sizes are only half of it. For Philippine import the documents travel with the crate: a FORM E certificate of origin under the ASEAN–China free trade arrangement supports the duty preference claim, and we supply the ICC clearance documentation and the test reports we supply with each order — thickness measurement, fragmentation count and, where the specification calls for it, heat soak records.
Send the glass schedule, thickness build-up and destination port to info@cnglassworks.com. We return a shop drawing for approval and a reference price within one working day, and nothing is cut until you sign the drawing.
Written 2026-11-19. Standard designations referenced as published. Sizes are manufacturing limits, not project guarantees.
Price from USD ___ per sqm FOB Qinzhou, depending on thickness, interlayer and quantity.
Last updated: 2026-11-22