Glass performance: acoustic, blast, solar, wind and seismic

Five requirements decide the build-up — acoustic, blast, solar control, wind load and seismic — and each is set by a number, not by glass thickness. China Glass Factory engineers each build-up at its own plant in Qinzhou, China, with heat-soak testing available on the shipment. Verified 8 November 2026.

The short answer

Performance is a property of the build-up, never of the glass type. "Acoustic glass" and "blast glass" are not products; they are assemblies. Each of the five requirements below is governed by a different variable — cavity for sound, interlayer for blast, coating for solar, panel size and support for wind, edge clearance for seismic — and a specification that names only a thickness satisfies none of them. The tables give the build-ups and the numbers, so a requirement can be checked rather than assumed.

Which five requirements decide the build-up?

RequirementGoverned byNot governed by
AcousticCavity width, dissimilar ply thickness, laminated dampingTotal glass thickness
BlastInterlayer type (SGP), frame and anchorageGlass thickness alone
Solar controlCoating type and position, gas fillTint darkness
Wind loadDesign pressure, panel size, support conditionHeight of the building
SeismicDrift capacity, edge clearance, interlayerGlass strength

What governs acoustic performance?

Single glazing has a coincidence dip — a frequency band where the glass and the air wavelengths align and sound passes through almost unhindered. Making the pane thicker only moves the dip; it does not remove it. A cavity plus dissimilar thicknesses does remove it, and a laminated ply adds damping on top.

Build-upApproximate RwTypical use
10 mm single tempered31–33 dBGeneral office, interior partition
6 + 12 air + 635–38 dBCity-centre residential
6 + 12 air + 8 laminated40–43 dBRoadside hotels, hospitals
8 + 16 argon + 8.76 laminated43–46 dBAirport-adjacent, high-traffic frontage

Three practical notes. The figures are laboratory values for the glass alone. In service, the frame and the perimeter seal usually decide the outcome — a good unit in a leaky frame performs worse than a plain unit in a sealed one. And for genuinely high performance, an asymmetric build-up (6 + 12 + 8 rather than 7 + 12 + 7) is worth more than an extra millimetre on both plies.

What governs blast resistance?

Blast-resistant glazing is not designed to stay intact. It is designed so that fragments remain bonded to the interlayer and the assembly stays in its frame, rather than becoming secondary fragmentation in the occupied space.

Threat levelTypical build-upNote
Low6 + 1.52 PVB + 6 laminated, tempered pliesFragment retention
Medium6 + 1.52 SGP + 6, or 8 + 1.52 SGP + 8Retains stiffness, stays in opening
HighMulti-ply laminated with SGP, engineered frameSystem design, not glass selection

The essential point: blast performance is a property of the whole assembly — glass, glazing gasket, frame profile, fixings and anchorage to structure. A glass-only quotation cannot demonstrate compliance, no matter what the interlayer is.

What governs solar control?

Build-upSHGC (approx.)VLT (approx.)Where it fits
6 clear + 12 air + 6 clear0.700.79Baseline; rarely acceptable in the tropics
6 Low-E (single silver) + 12 air + 60.400.65General commercial
6 Low-E (double silver) + 12 argon + 60.280.60Manila office and residential
6 Low-E (triple silver) + 16 argon + 60.240.55High cooling load, daylight still wanted
6 dark tint + 12 air + 60.450.35Only where reduced daylight is acceptable

In Manila the governing number is usually SHGC rather than U-value: the indoor-outdoor temperature difference is small, so conduction matters less than solar gain, and cooling load dominates the energy bill. Dark tinting lowers SHGC and VLT together, which trades cooling energy for lighting energy — usually a bad trade. A spectrally selective Low-E coating lowers SHGC while keeping VLT usable, which is why it is the default in tropical curtain walls.

Figures vary by coating supplier and unit construction. Ask for a spectrally measured report for the exact build-up, not a calculated estimate.

What governs wind load?

Thickness follows from three inputs, and none of them is "how tall is the building":

  1. Design wind pressure at that opening, from the local wind code, adjusted for height, terrain and exposure.
  2. Panel size — deflection rises steeply with the short span, so a wide panel is not equivalent to a tall one.
  3. Support condition — four-side, two-side and point-supported glass behave very differently, and point supports concentrate stress at the holes.

For architectural glazing the deflection limit typically governs before the stress limit: a panel can be strong enough and still visibly bow, which shows as distortion in reflection and can compromise the seal. Two elevations on the same building can legitimately need different glass because of height, corner location and local shielding.

What governs seismic performance?

In an earthquake the glass is rarely loaded by its own inertia; it is loaded by the building moving. A floor-to-floor drift of a few millimetres racks a rectangular opening into a parallelogram, and a rigidly glazed pane either cracks at the corner or transfers the load into the mullion.

In the Philippines this is a live issue on Mindanao and in older Metro Manila stock, where drift capacity was not part of the original glazing design.

Can one build-up meet several requirements?

Cost is saved by combining, not by choosing. A unit such as 6 Low-E tempered + 12 argon + 6 laminated carries solar control, thermal performance, acoustic improvement, safety and post-breakage retention in a single assembly. Where blast resistance is also required, the inner ply becomes SGP laminated. The build-ups do conflict in degree — acoustics want a wide cavity, solar control wants a coating, blast wants SGP — but they can be designed together. The mistake is to assemble a build-up from a catalogue and then test it, rather than design it against the requirements.

How is this glass shipped to the Philippines?

These build-ups are supplied to Philippine projects from our own plant in Qinzhou, with heat-soak testing available in-house for overhead and high-level glazing. Test reports for heat-strengthened and fully tempered flat glass are provided on request. The PS licence itself is held by the local manufacturer and the ICC is applied for by the importer. Shipments are quoted FOB Qinzhou or CIF Manila, Cebu or Davao, minimum one 20ft container. Duty and documentation are set out on the Philippines market page; Metro Manila and Cebu have their own pages.

Questions this page answers

How do I get a quieter facade? A cavity with dissimilar plies, not thicker glass. 6 + 12 air + 8 laminated typically reaches Rw 40–43.

What resists blast? SGP laminated glass sized to the pressure and impulse, in a frame and anchorage designed for it. Glass alone cannot demonstrate compliance.

How is solar gain controlled? A spectrally selective Low-E coating in an argon-filled cavity. Dark tinting trades cooling energy for lighting energy.

What decides thickness for wind? Design pressure, panel size and support condition — deflection usually governs before stress.

Does glass need seismic design? In seismic regions yes, and drift governs: laminated glass, edge clearance and a drift-compatible frame.

Can one build-up do several jobs? Yes — 6 Low-E tempered + 12 argon + 6 laminated covers solar, thermal, acoustic and safety at once.

Performance glazing price Philippines: Price from USD ___ per sqm FOB Qinzhou. The build-up, the coating and the laminating decide the rate, so a performance specification is quoted against your numbers rather than a list price.

What is the next step?

Send the performance requirements as numbers — Rw, SHGC, design wind pressure, drift, threat level — with the panel sizes and the fixing detail, and the build-up will be engineered against them. A specification that names only "double glazing" cannot be quoted accurately, because it does not yet say what the glass has to do.

Philippines market page Curtain wall and facade glass Insulating glass Laminated glass

Enquiries: info@cnglassworks.com — answered within one working day, in English.

Last updated: 2026-11-21. China Glass Factory, Qinzhou, China. Prices are indicative FOB Qinzhou and confirmed against your drawing.