Balustrade, shopfront, partition and glass door

China Glass Factory makes interior and retail glass in its own plant in Qinzhou, China — tempered, laminated, edge-worked and hole-drilled for balustrades, frameless shopfronts, office partitions, glass doors and shower enclosures, 7–15 days after order confirmation. The specification is decided by how the glass fails, not by how it looks. Verified 8 November 2026.

What glass goes into an interior fit-out?

Four applications, four different governing rules. A balustrade is governed by what happens after it breaks, so it is laminated. A shopfront is governed by deflection over the pane height, so thickness alone does not answer the question. A partition is governed by acoustics and by how the frame is fixed. A glass door is governed by the hardware that carries the leaf. Getting these four right is most of the difference between an interior package that passes inspection first time and one that gets remade.

Which glass for which interior application?

ApplicationUsual build-upEdgeWhat governs
Balustrade (public)10 tempered + 1.52 PVB + 10 tempered (or 12+1.52+12)PolishedPost-breakage retention, line load
Balustrade (point-fixed)12 tempered + 1.52 SGP + 12 temperedPolished, holesStiffness after breakage
Shopfront, framed10 mm temperedArrised / polishedDeflection over pane height
Shopfront, frameless12 mm tempered or 6+1.52+6Polished, flatWind load, mall barrier rules
Office partition10–12 mm tempered, single glazedPolishedAcoustic requirement, frame type
Glass door, framed6–8 mm temperedSeamedStile and rail system
Glass door, frameless10–12 mm temperedPolished, holesPatch fittings, floor spring rating
Shower enclosure8–10 mm temperedPolishedSafety glass, hinge cut-outs

Why is the interlayer the safety device on a balustrade?

Monolithic tempered glass breaks into small blunt dice. That is a good property for impact, and a bad property for a barrier, because the opening is then unguarded. A laminated panel keeps the fragments in place and stays in the frame.

InterlayerBehaviour after breakageWhere it belongs
PVB 0.76 mmHolds fragments, limited stiffnessInterior balustrades, low barriers
PVB 1.52 mmHolds fragments, standard barrier build-upMalls, condo podium, public interiors
SGP 1.52 mmRetains most stiffness; panel stays structuralPoint-fixed, cantilevered, crowd loading

Two details that decide whether the panel is compliant rather than merely present: the line load the barrier is designed for (commonly 0.75 kN/m for residential and 1.5 kN/m for public or crowd areas, but confirm against the local code), and how the bottom edge is held. A base-shoe channel behaves differently from a four-point fixed panel, and the glass thickness follows from that, not from the height.

Shopfront glass: is deflection or thickness the real limit?

The question "how thick should the shopfront glass be" has no answer without the pane height. A 3.5 m high pane deflects far more than a 2.4 m pane of the same thickness, and what fails an inspection is the deflection limit, not the stress.

In Philippine malls the governing requirement is often not wind at all — it is the tenant design criteria issued by the mall operator, which frequently requires laminated glass and a minimum barrier height at the shopfront line. That document should be read before the glass is ordered, not after.

Can a glass partition be single glazed, and how do you get acoustics?

Most office partitions are single-glazed 10–12 mm tempered glass in a dry-glazed or channel frame, and that is correct for visual subdivision. Where the partition has to control sound — a meeting room beside an open floor, a clinic, a plant room — the answer is not thicker glass. It is a cavity and dissimilar thicknesses, for example 6 + 12 air + 8, because a cavity breaks the coincidence dip that limits single glazing.

Build-upApproximate RwSuits
10 mm single31–33 dBVisual subdivision only
12 mm single33–35 dBGeneral office
6 + 12 air + 638–40 dBMeeting rooms
6 + 12 air + 8 laminated42–44 dBConfidential rooms, clinics

Note the qualifier: these are laboratory figures for the glass alone. In service, the frame and the perimeter seal usually decide the result — a well-chosen unit in a leaky frame performs worse than a plain unit in a sealed one.

What decides the glass door specification?

A framed door protects the glass on four edges, so thinner glass works. A frameless door hangs the leaf from patch fittings or a top rail, which means the glass carries the load, must be tempered, and needs polished edges and pre-drilled holes.

The detail most often missed in a quotation is the closer. A floor spring or concealed overhead closer has to be rated for the actual leaf weight — a 12 mm leaf at 1.0 × 2.4 m is roughly 72 kg, and an under-rated closer will either not hold the door open or will slam it. The second most common omission is the hole positions: they must be on the approved shop drawing before tempering, because glass cannot be drilled afterwards.

What causes most interior glass remakes?

Tempered glass cannot be cut, drilled or edge-ground after tempering. Every hole, notch, hinge cut-out, corner radius and edge polish has to be in the drawing before the glass enters the furnace. On interior packages this is the single largest source of remade panels, and it is entirely avoidable: approve the shop drawing, then release production.

How is interior glass shipped to the Philippines?

Interior and retail glass is supplied to Philippine projects from our own plant in Qinzhou. Test reports for heat-strengthened and fully tempered flat glass are provided on request. The PS licence itself is held by the local manufacturer and the ICC is applied for by the importer. Shipments are quoted FOB Qinzhou or CIF Manila, Cebu or Davao, minimum one 20ft container, production 7–15 days after order confirmation. Small-panel interior work is normally consolidated with facade glass in the same container to keep freight per square metre down — see the Philippines market page.

Interior glass price Philippines: Price from USD ___ per sqm FOB Qinzhou. Lamination, edge polish, holes and cut-outs are costed per panel, and small interior work is consolidated with facade glass in the same container to hold freight down.

What do interior contractors ask most often?

What glass should a balustrade use? Laminated, normally both plies tempered — 10+1.52+10 for public interiors, SGP for point-fixed or cantilevered panels.

How thick should shopfront glass be? It follows from pane height and support, not from a single number. Over 3.2 m or frameless, use laminated and check deflection.

Can partitions be single glazed? Yes for visual subdivision. For acoustic separation use a cavity with dissimilar thicknesses.

Framed or frameless doors? Framed protects the glass and allows thinner leaves; frameless needs tempered glass, polished edges, pre-drilled holes and a correctly rated closer.

Is tempered required for showers? In practice yes, and laminated where the enclosure is also a screen. Hinge cut-outs must be drilled before tempering.

What do we need to quote your interior glass?

Send the schedule with panel sizes, fixing detail and the acoustic or barrier requirement, and it will be quoted against the build-up that actually meets it. Two things make the first quotation accurate: the fixing method (base shoe, four-point, channel or patch fitting) and whether any hole or cut-out is needed, because both change the glass before it is made.

Philippines market page Tempered glass Laminated glass Speciality glass

Enquiries: info@cnglassworks.com — answered within one working day, in English.

Last updated: 2026-11-21. China Glass Factory, Qinzhou, China. Prices are indicative FOB Qinzhou and confirmed against your drawing.