Typhoon glazing for Philippine buildings: which glass, which interlayer, and the three mistakes to avoid
The short answer
In a Philippine typhoon zone, the glass that matters is laminated glass with a bonded PVB or SGP interlayer, normally in the exterior pane of an insulating unit, with the thickness set by the design wind pressure for that specific opening — not by a table of generic thicknesses. Monolithic tempered glass is not a substitute: it is stronger and it breaks safely, but after breakage nothing holds the pane in the frame. Choose PVB for ordinary commercial glazing; choose SGP where the glass carries structural or post-breakage load, such as full-height, point-fixed, cable-supported or overhead glazing.
Why is the interlayer the whole point?
Two different failures are routinely confused.
Injury failure is what tempered glass solves: it breaks into small blunt fragments rather than shards, so people are not cut. Containment failure is what typhoons actually cause: windborne debris strikes the pane, the glass breaks, and the question becomes whether the assembly stays in the opening. Once a pane leaves the frame, the building envelope is open, internal pressure changes, and the load path through the facade changes with it.
A laminated assembly behaves differently because the interlayer bonds the two plies. After breakage the glass is cracked but held, the unit keeps most of its in-plane integrity, and it stays in the frame long enough for the storm to pass. That is why laminated glass appears in the exterior position on debris-exposed elevations, and why tempered glass is used as the plies of that laminated build-up rather than instead of it.
PVB versus SGP — how do you choose?
| Condition | Interlayer | Reason |
|---|---|---|
| Standard commercial windows, shopfronts, residential | PVB, 0.76 mm or 1.52 mm | Adequate containment at the lowest cost per square metre |
| Full-height glazing, glass fins, large spans | SGP | Higher post-breakage stiffness; the pane keeps carrying load after cracking |
| Point-fixed, cable-supported or structural sealant facades | SGP | The glass is part of the structure; PVB is too soft for the residual load case |
| Overhead, canopy, skylight | SGP | Retention after breakage is a life-safety requirement, not a preference |
| Acoustic-critical facades near flight paths or traffic | PVB with acoustic grade, or a multi-layer interlayer | Damping performance rather than stiffness |
Cost discipline matters here: SGP on a project that does not need it is money spent for no engineering benefit, while PVB on a point-fixed facade is an under-specification that a consultant should catch at submittal stage.
Does thickness come from design pressure, or from a rule of thumb?
The sequence is fixed. The structural engineer derives the design wind pressure for the site from the NSCP wind provisions, adjusted for exposure category, building height and the tributary area of the specific opening. That pressure is then applied to the glass, with the appropriate safety factor for the support condition — four-side supported behaves differently from two-side or point-supported. Only then is a thickness chosen.
This is why two buildings on the same street can legitimately need different glass. A corner location at height with open exposure sees a different pressure from a sheltered mid-block opening at the same elevation. A supplier who quotes a thickness before seeing the design pressure is guessing.
Which three mistakes recur on Philippine projects?
1. Specifying "tempered" where "laminated" was meant. It is the most common substitution and the most expensive one, because it passes visual inspection and fails in the event it was specified for. The submittal must name the interlayer, not just the glass.
2. Leaving the interlayer type unstated. "6+1.52+6 laminated" does not say PVB or SGP, and the two are not interchangeable in price or performance. A quote without the interlayer named cannot be compared with another quote.
3. Sizing the interior pane as if it were the exterior one. In an insulating unit the exterior lite takes the impact and the interior lite provides the thermal and, in some assemblies, the secondary barrier. Treating them as equivalent ignores how the unit was engineered.
What does a complete submittal look like?
- Build-up stated in full: e.g. 6 mm tempered Low-E + 12 mm argon space + 6 mm tempered + 1.52 mm PVB + 6 mm tempered, with the interlayer material named
- The design wind pressure the assembly was checked against, in kPa, with the support condition
- Impact test evidence to ASTM E1886 / E1996 where the specification calls for debris resistance, with the test level stated
- Interlayer manufacturer's certificate for the batch
- For Philippine projects, the BPS registration number for laminated safety glass, with the current certificate copy
- Edge work and hole positions, since tempered glass cannot be cut or drilled after processing
What does China Glass Factory supply into this requirement?
Laminated glass with PVB or SGP interlayer, produced in-house up to 3,660 × 12,000 mm, combined with tempered, Low-E coated or ceramic-printed lites as the design requires. Tempered plies can be heat-soak tested to reduce the risk of spontaneous breakage from nickel-sulphide inclusions. Test reports for heat-strengthened and fully tempered flat glass are provided on request. The PS licence itself is held by the local manufacturer and the ICC is applied for by the importer, so we supply the test reports, scope and packing documents a tender needs. Philippine enquiries: info@cnglassworks.com.